When you purchase through links on our site, we may earn an affiliate commission. Learn more.
When you purchase through links on our site, we may earn an affiliate commission. Learn more.
Buy the Apex 300 if you want a permanently-sited home, RV, or off-grid backup with true 120V/240V split-phase from one box, and you’re prepared to wire it to a transfer switch and add the accessories your loads actually need. It’s a mistake for anyone expecting a grab-and-go portable power station or a plug-and-play whole-home replacement — at 84 lb with no built-in DC ports and a single-unit 240V ceiling of 16A, it is stationary infrastructure, not a camping unit, and not a one-box service upgrade.
The Apex 300 is Bluetti’s first unit to deliver simultaneous 120V and 240V split-phase from a single chassis with an integrated battery — the feature nearly every reviewer and owner singles out as the reason to choose it. It’s judged here against the question every buyer in this class faces: do you want a modular, scalable backbone you wire into your home or RV and grow over time, or a finished appliance you unbox and use? The Apex 300 is emphatically the former. It rewards the buyer who plans an installation and accepts that the base unit is a foundation — and frustrates anyone who reads “portable power station” on the box and expects USB ports, wheels, and whole-home coverage out of the gate.
A 3,840W continuous inverter that holds rated load — multiple testers sustained 3,800W for five minutes without thermal shutdown, and one ran two 15,000 BTU RV air conditioners plus a heater at 3,800W. The headline feature is real: it puts out 120V and 240V split-phase simultaneously from one unit while charging from a 120V wall outlet, which almost nothing else in its class does from a single box.
Base capacity is 2,764.8Wh, of which roughly 2,400Wh (about 87%) is usable at the wall in independent testing. Real-world owner runtimes: a cabin on lights and internet ran 5–7 days; a full cabin load including microwave drained it in about a day and a half; the rated 3,840W continuous load empties it in about 41 minutes. Plan capacity around your actual loads — and expand with B300K batteries if you need days, not hours.
A lot, and this is the real argument for the platform. Each B300K adds another 2,764.8Wh — the same capacity as the base unit’s internal battery — and one Apex 300 accepts up to six of them, reaching roughly 19.3kWh from a single head unit. Stack three units in parallel through the Hub A1 Parallel Box across eighteen B300Ks and the system tops out near 58kWh of storage and 11.52kW of output, true multi-day whole-home territory. You buy the ceiling you need now and grow into the rest one piece at a time, rather than paying for it all up front.
The 65-minute full recharge requires the optional NEMA L14-50P turbo cable, sold separately. The included 15A cable caps combined charging and bypass near 1,440W, stretching a full recharge to roughly 2.5 hours. Solar tops out at 2,400W on paper but realistically delivers well under that — see below.
No. The dual MPPT ports are capped at 60V, and multiple independent measurements landed around 790W per port in cold conditions and roughly 1,000–1,100W optimal — never the claimed 1,200W per port. Worse, the 60V ceiling can’t series standard 400W panels (74V VOC exceeds the limit), and the SolarX 4K accessory only starts at 150V, leaving a dead zone for 60–150V arrays. Plan solar around Bluetti’s low-voltage panels or budget for the SolarX 4K.
No, and don’t buy it expecting that. At 84 lb with no wheels and no suitcase handle, it’s a two-person lift and squarely stationary home/RV equipment. Bluetti positions it as home backup, and that’s how it should be used.
The base unit ships without USB or DC outputs of any kind and without the solar or turbo-charging cables — it’s deliberately unbundled. The single expansion port also means a DC Hub and an expansion battery can’t both connect directly; you chain the Hub through a battery’s second port. Budget for accessories, and know that the advertised one-box convenience comes after you’ve assembled the pieces.
This is the dominant, best-supported use case. Owners consistently deploy the Apex 300 — often two or three in parallel via the Hub A1 — wired to a transfer switch powering essential circuits: well pump, furnace, fridge, kitchen, bedrooms. The single-unit split-phase makes a one-box install simple where the prior AC300/AC500 generation needed a fusion box or paired units. Just know that one unit delivers 240V at 16A; 30A service needs two units, 50A needs three.
The dedicated TT-30R outlet and 50A capability let you plug an RV straight in, and the inverter handles AC startup loads competitors stumble on. The right buyer powers AC appliances and accepts that larger 12V house loads (slide-outs, leveling) still need a separate house battery — the base unit’s DC capability via Hub D1 isn’t enough for those.
Cold-weather operation is a quiet strength: one owner ran it at −15°C without pre-warming, a step up from a prior AC300+B300K setup that needed it. Paired with expansion batteries and a generator for cloudy stretches, it’s a capable plug-and-play alternative to a wired Victron-style system for buyers unwilling to do that integration.
Simultaneous 120V/240V split-phase from a single unit is the headline, and it’s earned. Across YouTube, editorial, and owner reports it’s the single most-cited reason to choose the Apex 300 — dual internal inverters deliver split-phase while the unit charges from 120V, and previous Bluetti generations needed fusion boxes or paired units to get there. For a buyer who wants 240V backup from one box, this is the reason to buy.
The integrated battery is the other real differentiator versus its own lineage. The AC300/AC500 were inverter heads requiring separate battery modules; the Apex 300 folds 2,764.8Wh into the chassis, and independent measurement puts energy density roughly 47% higher by volume than the AC300. Multiple owners traded up specifically for the integrated battery plus split-phase.
Standby efficiency is class-leading: independent bench tests measured 18–24.7W AC-on idle, against a measured 49W for an EcoFlow Delta Pro 3 and the older AC500’s 40W. If the unit sits in standby between outages, it sips. Build quality draws consistent praise — “beautifully built,” decisive switches, ammo-crate handles — and the app earns marks for fast pairing, TOU scheduling, and OTA updates.
The modular expansion ceiling is unusually high for the entry price, and it’s a core reason owners choose the platform. Every B300K adds a full 2,764.8Wh — the same capacity as the base unit’s internal battery — and one Apex 300 accepts up to six, reaching about 19.3kWh from a single head unit. Link three units in parallel through the Hub A1 Parallel Box across eighteen B300Ks and the system tops out near 58kWh of storage and 11.52kW of output: whole-home, multi-day capacity. Crucially you don’t buy that all at once. Reviewers and owners repeatedly cite the buy-one-piece-at-a-time path — start with the head unit, add batteries, a second or third unit, a Hub D1, or a SolarX 4K as needs and budget grow — as a decisive advantage over a fixed-capacity all-in-one.
The 2,400W solar rating is the biggest measured-vs-claimed gap. The 60V MPPT ceiling caps real-world input well below the spec — independent testers measured roughly 790W per port in cold and barely 1,100W pushing to 62V, never the claimed 1,200W per port. The ceiling also creates a 60–150V dead zone: the built-in MPPT stops at 60V and the SolarX 4K accessory starts at 150V, so arrays in between can use neither without reconfiguration. Owners upgrading from the AC300 (which accepted 12–150V) lose solar flexibility they previously had. Plan solar around Bluetti’s low-voltage panels, or budget for the SolarX 4K — and even a full three-unit SolarX deployment is capped around 3,600W in practice by the parallel charging cable, short of marketing’s aspirational numbers.
The base unit is not fully functional as purchased. No USB, no 12V, no car port — DC output requires the Hub D1 (an added purchase), and even then the car/barrel/USB ports share just 120W combined. Neither the solar PV cable nor the L14-50P turbo-charging cable is included. This is the recurring “unbundled” complaint, and it’s real: the low base price comes with a shopping list.
The single expansion port is a documented design trap. You cannot connect a DC Hub and an expansion battery directly at the same time — the workaround is to chain the Hub through an expansion battery’s secondary port, which means buying a battery you may not otherwise need. One owner who needed both DC and expansion reported this as a return-triggering surprise; it’s confirmed solvable but was not disclosed in Bluetti’s marketing.
One unit is 240V/16A, not whole-home. The marketing implies more single-unit muscle than the 16A reality; 30A service needs two units and 50A needs three. In 240V mode under light loads, technical owners measured the unit drawing 3–4× the consumed power from the grid via non-standard pass-through that cycles the battery continuously — Bluetti confirmed the behavior is intentional, but it undercuts the efficiency story for anyone running small continuous loads and raises long-term battery-wear questions. The 18–24.7W idle figure is standby-only; it does not describe inverter-on light-load operation.
The Apex 300’s whole design is a deliberate trade: integrated battery plus single-unit split-phase came at the cost of internal space, which is why the solar controller is undersized and the DC ports were moved off the chassis. You’re buying a more compact, more capable inverter core in exchange for an accessory ecosystem you assemble yourself.
The modular “buy the base, scale later” model is a strength for staged budgets — start with the unit, add B300K batteries, a Hub D1, or a SolarX 4K as needs grow — but it’s the same property that makes the base unit feel incomplete out of the box. Reviewers fairly characterize it as cost-cutting that pushes spend downstream; whether that’s a feature or a frustration depends entirely on whether you walked in planning an installation or expecting an appliance.
One non-obvious lineup reality: the B300K and B500K batteries “for Apex 300” are distinct part numbers from the AC300/AC500 variants despite shared names. Owners report the standard B300K is backward-compatible with the AC300/AC500, but verify before mixing across generations.
The Apex 300 sits at the accessible end of the home-battery tier: lower entry price, lower single-unit output and capacity than the EcoFlow and Anker flagships, and a modular path upward. Buyers who need substantial capacity or heavy 240V loads from a single box move up to the DELTA Pro 3, DELTA Pro Ultra, or F3800. Buyers who only need 120V and want more onboard battery for the money look at the Jackery HomePower line. The Apex 300’s pitch is single-unit split-phase at a low entry point with room to scale — up to about 19.3kWh on one head unit and roughly 58kWh / 11.52kW across three units — and you pay for that with an unbundled base and a solar input that disappoints relative to its rating.
| Model | Capacity | Rated output | 240V? | Key difference vs Apex 300 | Choose it instead if | Buy |
|---|---|---|---|---|---|---|
| Bluetti Apex 300 | 2,764.8Wh (exp. 58kWh) | 3,840W | Split-phase, single unit | — | — | Check Price |
| EcoFlow DELTA Pro Ultra | 6,144Wh (exp. 90kWh) | 7,200W | Yes | Far larger capacity and output per unit, 0ms UPS, IP54 outdoor-rated | You want a higher-capacity whole-home-class core in one larger unit and don’t mind the bigger footprint and price | Check Price |
| EcoFlow DELTA Pro 3 | 4,096Wh (exp. 48kWh) | 4,000W | Yes | Higher single-unit capacity and split-phase output, faster AC recharge | You want more usable capacity and output per box without stacking units | Check Price |
| Anker SOLIX F3800 | 3,840Wh (exp. 26.88kWh) | 6,000W | Yes | Higher continuous output and built-in 240V at a single-unit level | You need more inverter headroom from one unit for heavier 240V loads | Check Price |
| Jackery HomePower 3600 Plus | 3,584Wh (exp. 21kWh) | 3,600W | No (120V) | Larger single-unit battery but 120V only | You only need 120V and want more onboard capacity per unit | Check Price |
Not as a single unit in any meaningful sense. One unit delivers 240V at only 16A — enough to power a set of essential circuits through a transfer switch, but 30A service requires two units and 50A requires three. Owners running near-whole-home setups stack three units in parallel via the Hub A1 Parallel Box with up to eighteen B300K batteries total (six per unit) — roughly 58kWh of storage and 11.52kW of output. For essential circuits (well, fridge, furnace, lights, internet), one unit plus an expansion battery is a realistic backup, and a single unit accepts up to six B300Ks for about 19.3kWh; for true whole-home, plan a multi-unit system.
It has UPS functionality, but the 0ms switchover headline is conditional — it requires 240V output, grid connection via the 15A AC input, and loads on the two left NEMA outlets; other configurations measured ≤20ms in bench testing. Wired to a manual transfer switch, you still flip the switch yourself. One owner reported an error code if the unit stays grid-connected during an outage, resolved by cutting the breaker feeding the unit when power drops — get that sequence right at install.
This is documented behavior, not a defect. In 240V mode under light continuous loads, the non-standard pass-through draws extra grid power to keep the battery topped while supplementing from it — technical owners measured 3–4× the consumed power, and Bluetti confirmed it’s intentional. The well-publicized 18–24.7W idle figure is standby-only and doesn’t apply with the inverter running under load. If you run small continuous loads, this undercuts the efficiency advantage and cycles the battery more than you’d expect.
If solar flexibility with higher-voltage arrays matters, the AC300 accepted 12–150V where the Apex 300 caps at 12–60V — a regression for certain array configurations. Owners upgrading specifically for split-phase have flagged losing solar compatibility they previously had. The Apex 300 wins on integrated battery, split-phase from one unit, and standby efficiency; the older platform can be the better solar generator for arrays producing 60–150V. Match the choice to your panels.
Yes. The base unit has zero built-in DC output — no USB, no 12V, no car port. The Hub D1 adds them but its car/barrel/USB outputs share just 120W combined; the useful DC feature is its high-amperage Anderson port (12V/50A or 24V/25A, up to 700W). Some owners simply run a mains-powered USB charger off an AC outlet as a cheaper workaround. Factor the Hub into your budget if DC matters to you.
Multiple owners report buying renewed Apex 300 units from Bluetti’s eBay store in mint condition, sometimes with a free panel, and noted the eBay receipt doesn’t list them as refurbished. Separately, one buyer received a clearly used unit sold as “New” on Amazon and endured a painful return that cost them a federal tax-credit window. If condition and clean documentation matter, the renewed eBay channel has drawn better feedback than the “New” Amazon listings for this product.
The Apex 300 is the unit to buy when you’re building a system, not shopping for a finished gadget. Its split-phase-from-one-box trick is the real thing, its build is excellent, and its standby efficiency leads — but every one of those strengths is in service of a permanently-sited installation, and the product punishes anyone who misreads “portable power station” on the box. The solar rating is optimistic, the base unit needs accessories to reach its potential, and the single-unit 240V ceiling is lower than the marketing implies. None of that is disqualifying for the buyer it’s built for: someone wiring it to a transfer switch or RV shore connection, expanding deliberately, and valuing one-box 240V over an all-in-one appliance. Walk in with an installation plan and the accessory budget to match, and the Apex 300 is one of the most sensible split-phase backbones you can buy. Walk in expecting wheels, USB ports, and whole-home coverage out of the carton, and you’ll be the owner writing the angry review. Know which buyer you are, and the answer is clear.